8 Common Plumbing Problems and Solution

8 Common Plumbing Problems and Solution

Plumbing problems can quickly shake up our habits. We are so used to having access to water that as soon as a situation complicates the process, several common actions that we take daily are affected.

Indeed, even the smallest malfunctions of plumbing can have a big impact on our lives. This is why it is best to act quickly when you notice that something is wrong.

In this article, we’ll cover some of the most common plumbing problems, along with some tips for making proper repairs.

Here are the 8 most common plumbing problems and what you can do about them.

 1 – Sewage odors in the house.

A buildup of dirt in the pipes is sometimes responsible for bad odors in the kitchen or bathroom. Sewer odors can also come from the sewage disposal system causing slower drainage as well.

The solution

The set of pipes ensuring the proper functioning of the pipes and aeration is called the vent. The latter starts from the roof and joins the sewer or individual sanitation according to very specific rules.

Bad odors in the house can come from a blocked vent (by a bird’s nest for example) causing poor air circulation. Bring a professional to unblock the vent and have a cap or wire mesh strainer installed to remedy this problem.

2 – Odors in the bathroom

This is a common problem for homes that have a septic tank. Septic tanks use the bacteria that thrive in the tank to break down organic waste. Due to the harmful products that people use, the bacterial colony is affected and this impairs the rate of digestion of organic waste.

As a result, organic waste is evacuated to the leaching field before being completely digested, resulting in blockages. These blockages lead to leaks that end up contaminating the groundwater. In some cases, backdrafts can occur in the house and this will cause the bathroom to smell foul of hydrogen sulfide (smell of rotten eggs).

The solution to this plumbing problem:

Bio-Sol shock treatment products should be able to get your septic system back to good working order. To do this, it is enough to introduce billions of bacteria and enzymes into the septic tank. These bacteria immediately begin to digest organic waste, which eventually unclogs the leaching field.

3 – Tap water goes all over the place

There is a good chance that the aerators inside your faucet are defective. These are either dirty, full of limestone, or downright broken.

The solution

You can also have the aerators replaced or the tap directly replaced, because if the aerators are worn out, the mixer must also be dated.

A professional plumber usually has these fairly standard parts and can intervene for a small plumbing repair or replacement of the mixer for less than $ 100.

4 – leaky faucets

It is one of the most common plumbing problems in most homes. Leaky faucets are not only annoying, but they also waste a lot of water in the long run. A small leak may not seem like a big deal, but the cumulative effect is huge.

For example, a leak of 10 drops every minute ends up wasting 300 gallons of water per year. If you have a septic tank, a leaking faucet can contribute to hydraulic overload in the septic tank and this can interfere with the digestion of organic waste. Faucet leaks are usually caused by worn washers or O rings, so they are relatively easy to repair.

 Solutions to Leaking Faucet Plumbing Problems

Step 1: Close the hot and cold water supply valves. They are usually found under your sink. If you can’t see them under the sink, turn off the main meter for the whole house.

Once this is done, follow the next steps depending on the type of faucet you have.

 Repairing a leaking compression valve

Step 2: Remove the cap from the handle. You can do this by removing the handle screw and then gently applying pressure under the handles to remove them.

Step 3: Loosen the hood nut using an adjustable wrench. Remove the stem from the faucet by unscrewing the screw that holds the washer on the stem.

Step 4: Attach a replacement washer to the stem, then reinstall the stem, hood nut, and handle.

 Repairing a leaking two-handle washerless faucet

Step 2: Access the socket the same way you would a compression faucet, then start with the valve handle working your way down.

Step 3: Remove the socket then replace it with a new one.

Step 4: Reinstall the rod, hood nut, and handle.

 Repairing a leaking single-handle washerless faucet

Step 2: The exact method of removing the valve sleeve varies depending on the manufacturer. However, the first thing to remove should be the handle screw which is usually located under the handle, although it can sometimes be under a hood on top of the handle. You can then unscrew the handle of the faucet.

Step 3: Loosen the nut to reveal the valve sleeve, then remove the clip that holds the valve sleeve, remove the sleeve and replace it with the new one.

Step 4: Reinstall the hood nut and handle.

5 – The piping makes noise

Your pipes make a thudding noise when you open and close your taps: this is called a water hammer. Again, this is a problem of sudden pressure variation. You have to fix this to prevent your pipes from becoming deformed or worse yet, that they end up giving way causing water damage.

The solution

Several solutions exist to remedy the water hammer. You can invest in a pressure regulator, replace your faucets with slow-closing faucets or install an anti-pulsation bottle or anti-water hammer.

6 – Slow or clogged drains

A slow or clogged drain can be annoying. Not only does the water flow too slowly, but it also leaves a greasy residue in the tub and sinks when the water finally drains. Slow, clogged drains are caused by many factors including, but not limited to, debris getting lodged in pipes. If only one drain in the house is slow then the problem is only in that drain and solving it will be easier and faster than when the problem is in the whole house.

The solution to this plumbing problem:

  • If you have a septic system, chances are the problem is either caused by a faulty septic tank or septic field. If so, shock treatment with Bio-Sol’s products and will solve the problem by introducing billions of bacteria into the septic tank. These bacteria digest organic waste, also treating the problem in the septic field.
  • If the problem is in one drain, debris may be blocking the pipes. You can try using a good old siphon to unblock the drains.
  • If the siphon fails to unclog the drains, you can try using the fish technique to unclog the drain manually. Take a long thread and “meander” down the drain as far as you can. If you feel that debris is blocking the wire, wiggle it until it comes loose and finally remove your wire and rinse some water in the hose. Once this is done, add an eco-friendly drain unblocker to remove organic debris that might still be stuck in the drains (the SeptiDrain is recommended).
  • If none of the above methods work, call a plumber for help as this is a complex issue.

7 – Water rises to an inappropriate place

If the water is in the sink and the water comes up through the shower or the tub then it is a sign of a blockage in your pipes.

Indeed, the water has to flow by a particular drain, if this one is blocked the water takes the opposite way and then runs through the rest of the installation (see diagram).

The solution

A professional plumber such as Knoxville Plumbing must intervene to unblock your pipes. Usually, it detects fairly quickly where in your installation the plug may have been installed. This must be remedied as soon as possible so that the situation does not get worse.

It is not recommended to use Desktop style unblockers. These weaken your pipes enormously and nibble them from the inside, the problems could be more important.

The prices are too high in the home repair industry, especially when it comes to plumbing. A pipe unblocking costs, labor, and travel included, between 170 and 250 $. If the problem is more and requires the interfere of a clearing truck, the professional plumber would be able to tell you this quickly to avoid unnecessary intervention.

8 – Irregular water temperatures

Besides the fact that inconsistent water temperatures are bothersome, it is also a health hazard. For example, if the shower dispenses water that is too hot, the user can easily suffer from burns. \

Additionally, water above 44.44 ° C (112 ° F) can damage your lipid layer. Even though the ideal hot water temperature for showering is 112 ° F (44.44 ° C), the shower can release water that is as hot as (140 ° F (60 ° C) But it is not only a water problem, it is also possible to get sudden bursts of cold water and it can be really surprising.

The solution to this plumbing problem:

  • In some cases, water temperature fluctuations are caused by competing devices, so make sure this isn’t the case before you think of another solution. For example, a dishwasher starts up; it could make the shower cool.
  • Check the water heater settings to make sure the settings are correct.
  • If the hot water settings are as expected and a competitor’s appliance is not causing the temperature fluctuations, it would be a good idea to call a plumber to investigate the problem.

Conclusion

We can say in conclusion that a plumbing problem can arise at any time and, above all, at the wrong time. This may cause discomfort daily. Thus, it is important to always remember to properly maintain your plumbing system regularly.

Many variables affect how long your plumbing will run before you need to hire a professional plumber from Knoxvilleplumbing.com. That said, there are also some plumbing issues that you can fix on your own without having to spend the money on a plumber.

You may also like...

Leave a Reply

Your email address will not be published. Required fields are marked *